Schiit Skoll


Schiit Skoll er trolig en av de aller beste og mest fleksible RIAA-trinnene på markedet i sin prisklasse

  • Velg mellom balansert XLR eller RCA tilkobling – på både inngang og utgang!
  • Kompatibel med både MM- og MC-pickuper og med mange justeringsmuligheter
  • Justerbar gain fra 40dB til 70db(!)
  • LF-Filter
  • Kan betjenes med fjernkontroll!

Tilgjengelighet På lager (kan også restbestilles)

Produktnummer: SSKOLL Kategori:

Skoll is the highest performance, most flexible, least expensive balanced phono preamp available today. Put it in your system, sit down in your chair, and adjust everything with the included remote control. You’ll give up nothing to the big-boy phono preamps out there—while keeping a much fatter wallet!

Over the Top Performance

Skoll is insanely quiet and accurate—and it does this with uber-simple, fully discrete, differential Class A zero feedback gain stages and a fully passive RIAA network. Or, in English, there’s not an op-amp in sight. Skoll’s gain stage is compound JFET-BJT pair running on massive 64V rails for enhanced linearity and freedom from overload. The result is over 100dB signal to noise ratio for 40dB of gain, and up to 70dB of gain on tap.

Flexibility Without Penalty

Is your turntable single-ended or balanced? Don’t worry. There’s no performance penalty for either balanced or single-ended input or output. And with four gain levels, it’s ready for virtually any cartridge, from MM to MC to MI. Add relay-switched inputs for two turntables, plus relay-ladder loading for both R and C values, as well as a switchable passive LF filter, and Skoll delivers all the flexibility you need without penalty. We even went so far as to post-filter the relay power supplies and make the microprocessor turn off when not in use, in order to keep Skoll exceptionally noise- and interference-free.

Adjust Everything from Your Listening Chair

Here’s where it gets good. Skoll includes a remote control, so you can adjust literally everything without getting out of your favorite listening chair. As in, you can:

  • Select input: choose balanced or SE input
  • Change gain: choose 40, 50, 60, or 70dB
  • Change resistive loading: Choose 47k, or 10, 50, 100, or 150 ohms
  • Change capacitive loading: choose 50, 100, 150, or 200pF
  • Select LF filter: choose no LF filter, or engage the 2-pole/15 Hz passive network

Designed and Built in Texas

By “designed and built in Texas,” this is what we mean: Skoll was designed and built at our Corpus Christi, Texas facility, and the vast majority of the total production cost of Skoll—chassis, boards, assembly, etc—goes to US companies manufacturing in the USA. Our chassis are made in California. Our PCBs are done in Nevada. Yes, the wall-warts are made overseas, but there’s some give and take at this price point.

TYPERMoving Coil Pickup, Moving Magnet Pickup


Gain: enough for all turntables, all cartridges
Noise: insanely low for a turntable, you’ll be hearing the pops not the hiss
Distortion: 10-100x lower than any record you’ll play
Heat: top gets moderately warm; nothing to worry about, we make stuff that runs waaaaaay hotter for years and years
Size: smaller than a typical rack product, but probably not small enough to hide behind the turntable


Gain: 40db
THD: <0.006%, ref 4V RMS balanced, 2V RMS SE
SNR: >102dB, A-weighted, ref 4V RMS balanced, 2V RMS SE
Crosstalk: -100dB, 20-20kHz
Sensitivity: 2.85mV for 300mV output at 1kHz

Gain: 50dB
THD: <0.02%, ref 4V RMS balanced, 2V RMS SE
SNR: >90dB, A-weighted, ref 4V RMS,2V RMS SE
Crosstalk: -98dB, 20-20kHz
Sensitivity: 0.78mV for 300mV output at 1kHz
Gain: 60dB
THD: <0.03%, ref 4V RMS balanced, 2V RMS SE
SNR: >85dB, A-weighted, ref 4V RMS balanced, 2V RMS SE
Crosstalk: -95dB, 20-20kHz
Sensitivity: 0.34mV for 300mV output at 1kHz
Gain: 70dB
THD: <0.06%, ref 4V RMS balanced, 2V RMS SE
SNR: >70dB, A-weighted, ref 4V RMS
Crosstalk: -84dB, 20-20kHz
Sensitivity: 0.09mV for 300mV output at 1kHz
Maximum Output: 20V RMS balanced, 10V RMS SE
Overload Margin: >20dB
RIAA Accuracy: +/- 0.15dB, 20-20kHz
Low Frequency Filter: switchable 2 pole at 15 Hz, fully passive, for balanced XLR outputs 
Output Impedance: 10 ohms
Input Loading: 10, 50, 100, 150, and 47k ohms resistive, and 50, 100, 150, or 200pF capacitive, switched via remote or front-panel button
Topology: Equipoise™ balanced, differential, fully discrete zero feedback gain stages, passive RIAA, 0.1% thin-film resistors, and 1-2% film capacitors, switchable passive CR LF filter, microprocessor oversight and relay switching, remote control
Power Supply: “wall wart” style 24/6VAC transformer, dual-filtered, regulated +45V/-19V rails, plus 5V/3.3V supply for microprocessor and relays
Power Consumption: 7W
Size: 9 x 6 x 1.5”
Weight: 2 lb
Duet Audio AS
Skroll til toppen